1. 3DS Blog
  2. Brands
  3. DELMIA
  4. On a Fixed-Price Automotive Line, Engineering Errors Are Margin

ManufacturingNovember 17, 2026

On a Fixed-Price Automotive Line, Engineering Errors Are Margin

On fixed-price automotive work, engineering errors come straight out of your margin, but simulating cells, tooling and robot programs in a virtual plant catches them before anything is built. I explain how in this article.
header
AvatarBuddharatn Ratawal

Table of contents

Robot programming accounts for roughly 40% of the total cost of implementing a robotic workcell, ahead of feeders at 25% and grippers and tooling at 19%, according to the Joint Research Centre, European Commission. For a line builder quoting fixed price work, that is the largest single block of cost in the bid and the one most exposed to being wrong.

The most expensive mistakes are the ones discovered after installation: a robot that cannot reach a weld, a fixture that collides with a torch or a cell that takes more floor space than needed. Each one means rework, moved equipment and lost production time, and on a fixed price contract most of that lands on your side of the deal.

That is where robotics simulation and offline programming change the economics: engineers test layouts, tooling and robot programs in a virtual plant before anything is built or stopped. The examples below come from line builders and integrators serving automotive customers.

1. Right-size work cells before you build them

Floor space and equipment counts are fixed early in a project and expensive to change once the price is agreed. Simulating them against the real plant is the cheapest time to get them right, and the only time the saving is still yours to offer.

  • A quarter less floor space. Italian integrator Robot at Work simulated a plant with more than 12 cells for a customer adding automated guided vehicles. The simulation showed the customer needed only three-quarters of the floor space it had planned.
  • Five cameras down to one. For an automotive customer with a vision system on an assembly unit, Robot at Work designed a new robotic setup virtually that let one camera monitor the part as well as five had before, without hurting quality. The customer reused the setup on other lines.
  • Mezzanine height and placement. Automotive line builder Prodomax built a new cradle line virtually, with welding paths, material handling and operator stations, and used it to set the minimum height and position of a mezzanine level.

2. Resolve tooling conflicts in simulation, not on the installation floor

Once a line is on the customer’s floor, there is very little downtime to fix mistakes and no appetite to pay for them. Prodomax designs customized automotive-part lines for OEMs and Tier 1 suppliers and simulates each one inside the customer’s plant, covering robot reach limits and tooling interferences.

Static reach studies could not show robot paths. Simulating every motion can. Prodomax reports that since adopting simulation, it has not had to move a single robot because of an engineering error. When one customer added equipment after the line was on site, the team checked in the simulation that the existing robots could still move around it.

The workflow also shortens the loop with tooling design. Engineers create weld torch clouds in simulation and export the CAD data to the design team, which builds tooling around them in SOLIDWORKS and quickly identifies interferences. Testing weld guns from a library against every weld point in the same way identifies the smallest set of guns a plant needs, reducing spare parts.

3. Absorb multi-variant and EV launches without absorbing the engineering cost

More variants and new EV platforms mean more robot programs and more design changes, and OEMs expect their line builders to carry that volatility inside the quoted price. The cost depends on how quickly a change can be turned into a validated program.

  • Changeovers in about a day. Some of Robot at Work’s customers change production two to three times a month. Because the team simulates each change in advance, a new production cycle can be up and running within a day, with minimal downtime.
  • Design changes in a few clicks. Line builder CIS Optim’Axes uses robot simulation with SOLIDWORKS to update, simulate and validate its work when a customer’s product evolves.
  • One change, every instance. At Prodomax, amending a single CAD item, such as a tip dresser, updates every instance in the machine. Function templates carry over to other projects, and robots from several manufacturers can be swapped within the same work cell.

New EV-body structures, battery assembly processes and powertrain configurations raise the stakes since each needs robot programs built from scratch. Simulating these programs alongside product design, rather than after it is frozen, is what keeps those launches on schedule and the change orders off your margin.

4. What customers report on programming and commissioning

On top of these project-level savings, one DELMIA customer reported an 80% reduction in robot programming time. DELMIA reports up to 75% less physical commissioning time for DELMIA Robotics projects. The return on investment is typically inside the first year. Results vary with line size, robot mix and how much existing code can be reused.

Prodomax describes the effect on schedules. They state that some lines now have only a few weeks to get up and running. Simulating the system ahead of time greatly shortens the time between power-on and production.

Read the ABI Research report that ranked DELMIA first for offline programming software in industrial manufacturing.

Take the next step

FAQs About Robotics Simulation

In avoided rebuilds: oversized cells, reach and tooling conflicts found on the customer’s site, and slow changeovers for new variants. On fixed price work each of those is unrecovered cost. The examples above show all three.

Customers using DELMIA Robotics typically report return on investment within the first year, based on programming and commissioning savings. The timeline depends on line size and how much existing code can be reused.

DELMIA Robotics supports over 2,000 robot models and is PLC agnostic. Prodomax mixes robots from several manufacturers inside one simulated work cell.

Offline programming prepares and validates robot programs without stopping production. Virtual commissioning then tests those programs against PLCs and controllers before start-up.

Customer Robot at Work was up and running within a couple of months with partner support and training. Role-based packages let each engineer start with the tools for their job.

DELMIA, a brand of Dassault Systèmes’, provides a unified environment for designing, simulating, programming, and commissioning robotic systems using a physics-accurate virtual twin. Built on the 3DEXPERIENCE platform, it supports 2,000+ robot models, multiple PLCs and all major processes, generating validated trajectories and native robot code from a single data model. The virtual twin, combined with AI-assisted automation, cuts programming and commissioning time while enabling fast, reliable adaptation to product or production changes.

Stay up to date

Receive monthly updates on content you won’t want to miss

Subscribe

Register here to receive updates featuring our newest content.